How To Reset Toyota Highlander Maintenance Light? [Step-by-Step]

Some people find it distracting and unsettling to have a yellow engine or maintenance light on their dashboard while they are driving.

This can be an annoyance.

If you take your Toyota Highlander in to have it maintained or tuned up, the mechanics will typically reset the maintenance light on the dashboard.

However, this is not always the case and you should not rely on them to do so.

When a driver has already spent a significant amount of money on repairs, yet this indicator is still illuminated, it causes them concern.

You’re in luck since there’s a simple way How To Reset Toyota Highlander Maintenance Light that’s been on in your Toyota Highlander.

Changing the Setting on the Toyota Highlander’s Maintenance Light

If you would rather reset the maintenance-required light on your Toyota Highlander from the comfort of your own home, you can do it by following these steps:

After inserting your key into the ignition switch, turn the dial to position one (the first set before actually starting the car).
After turning the key to position two, you should quickly push and hold the odometer button that is located on your dashboard.
Keep pressing and holding the button for the odometer for around ten seconds. You should notice that the maintenance light has begun flashing, and there may also be a beeping sound. After then, the light should be turned off.
After the maintenance indicator light has gone out, take your finger from the odometer button before turning the key to start the vehicle. Once your Camry has started, the light should no longer be on. To turn off the maintenance light on the Toyota Camry, you will need to repeat this method one or two more times, if it is still illuminated.

What Does the Light Mean When It Says Maintenance Is Required?

The “MAINT REQD light” message that appears on your dashboard is the Toyota maintenance indicator light.

It’s a light that stays on all the time, letting you know that you need to get your oil changed at a place that’s been inspected and approved by the government.

Performing regular oil changes on your Toyota can help increase the vehicle’s fuel efficiency and make the engine function more smoothly.

Additionally, it will lessen the amount of wear and tear on the components, which will result in significant cost savings in the long run.

This warning light will come on every 5,000 miles as a reminder to replace the oil in your vehicle, and it will turn on automatically after each milestone.

It is essential to be aware that the presence of the light on your dashboard does not necessarily indicate that your vehicle has sustained damage.

As a result, you can continue to use your new vehicles without risk even if the light is illuminated.

Because the Toyota maintenance light counts those 5,000 miles solely based on the odometer’s readings, it has no method of determining whether or not the oil has been changed in the interim.

Because of this, the light can be really bothersome if it flashes on your dashboard shortly after you have changed your oil and it is telling you to do it again.

It is possible that the mechanics who service your Toyota vehicle/Toyota car will forget to turn off the maintenance required light, in which case you will have to do so yourself.

What do I need to do to turn off the Maintenance Required Light?

The process of resetting is, thankfully, not at all hard, and it is compatible with the vast majority of Toyota models.

It is a good idea to understand how to do it on your own so that you may avoid having to make another trip to the auto shop simply to have it reset.

1. Start the engine of your vehicle.

Make sure the key is in the on position and check the information displayed on the dashboard. Instead of showing the trip meter, the odometer should read out the miles traveled.

2. Power down the vehicle and hit the button to clear the trip odometer.

After you have turned the key off, you will need to make sure that the maintenance necessary light is turned off by pressing the button that is located on the trip meter reset. Keep your finger on this button for a time. This is the button that, on some models, allows you to go from viewing the odometer to reading one of the other two trip meters.

3. Restart the Engine of the Vehicle

While holding down the reset button, move the key to the “on” position with very light pressure. Check to see that it is in this position rather than the “start” one, which is the one that activates the engine. Now, give the odometer your whole focus and attention.

4. Maintain depressing the button labeled “Reset.”

Check to see that the button for resetting the trip meter is still pushed while you are looking at the odometer. The odometer will begin to show a string of dashes on the screen in the following format: After some time has passed, a string of zeros will start to appear. Keep pressing the button until the display on the screen returns to its usual odometer reading.

5. Let go of the button labeled “Reset.”

After the normal odometer readings have been displayed on the screen, you may now let go of the reset button and start the engine of your vehicle.

It is expected that the maintenance required light will no longer illuminate on your dashboard.

If the light continues to show up, you will need to go through the method once more until the maintenance light disappears from your dashboard.

Because you reset the maintenance required light manually, its counter is been reset to zero.

It will keep counting the miles that have been driven off of the odometer until it reaches the mark of 5,000 miles.

When this occurs, the warning light will flash on and off again on your dashboard.

If the mechanics at your car shop are unable to turn off this warning toyota maintenance required light, you will need to do it yourself by repeating the instructions outlined above.

It is important to keep in mind that the procedure for particular Toyota Corolla models may vary slightly from one another.

It’s possible, for instance, that you have to maintain pressure on the toggle knob of the odometer for twenty seconds while turning the key off. After you have completed that step, turn the key back on, but do not start the vehicle.

On your dashboard, the maintenance reminder light should start flashing at this point.

Hold the button down until the indicator light on your dashboard turns out.

You must continue to do this. It is essential to maintain pressure on the reset button for at least twenty seconds in order for this method to be effective.

Why Is It Necessary for You to Turn Off the Maintenance Light?

Because the Toyota maintenance light does not go off by itself, it is in your best interest to switch it off manually so that there is one fewer thing to distract you on your dashboard.

As you navigate the streets of the city, this Toyota check engine light may start to annoy you, and it may even lead you to believe that there is something wrong with your vehicle.

In a similar vein, if a member of your family drives your Toyota and is unfamiliar with the significance of this indicator light, that person may become anxious and fear that the vehicle has been harmed.

Second, you can reset the maintenance light on the counter by turning it off and then back on the maintenance necessary light once you have completed the oil change.

As a consequence of this, you will be able to drive securely on public roads, and after 5,000 miles, this light will notify you that it is time for a new oil change.

As a result, you will not have to manually tally the miles driven.

Toyota Models

Toyota RAV4
Toyota Land Cruiser
Toyota Tacoma

FAQ on How To Reset Toyota Highlander Maintenance Light

How do you turn off the maintenance-required light on a Toyota Highlander?

After turning the key to position two, you should quickly push and hold the odometer button that is located on your dashboard. Keep pressing and holding the button for the odometer for around ten seconds. You should notice that the maintenance light has begun flashing, and there may also be a beeping sound. After then, the light should be turned off.

How do you reset the maintenance required light on a Toyota?

Insert your key into the ignition and turn it to position one, which is the position just before the start button on the dashboard. Turn the key to position two, then push and hold the button that resets the trip meter that’s located on the dashboard. Keep pressing and holding the button for the odometer for the next ten seconds. After that, the light should blink, followed by a possible beep, and then it should turn off.

What does the maintenance required mean on the 2018 Toyota Highlander?

The “MAINT REQD” message that appears on your dashboard is the Toyota maintenance indicator light. It’s a light that stays on all the time, letting you know that you need to get your oil changed at a place that’s been inspected and approved by the government.

Why is my maintenance required light still on after the oil change?

In the vast majority of cases, this simply indicates that your car is in need of an oil change. In the event that the distance driven is greater than 5,000 miles after the maintenance data has been reset, the warning light will turn on and remain lit.

How do you reset the oil change light?

To begin, turn the key in the ignition….

While simultaneously applying full pressure to the brake pedal as well as the accelerator pedal,

Always keep a firm foot on both the throttle and the braking pedal.

After three seconds, a notification appears on the screen verifying that the procedure to reset is now being carried out.

JoJiela Magsisi

Writer at Discover Seldric | + posts

Meet Jojiela Magsisi, a fervent car lover and gifted writer whose love affair with automobiles goes beyond the rev of an engine and the gleam of chrome. With a unique perspective and a talent for storytelling, Jojiela brings a fresh voice to the world of automotive journalism.

How To Reset Toyota Highlander Maintenance Light? [Step-by-Step]

Changing the Setting on the Toyota Highlander’s Maintenance Light

What Does the Light Mean When It Says Maintenance Is Required?